Visonic POWERMAX - Specifications download pdf (Page 32)

32 D-300885

D10. Perimeter Follower Zones

A non-entry/exit zone, typically a perimeter zone located

on an entry/exit path, that is treated as an entry/exit zone

during an entry/exit time.

D11. 24-Hour Zones

24 hour zones are mainly used for PANIC buttons, perimeter

detectors and anti-tamper protection. They therefore trigger an

alarm in both armed and disarmed states.

• 24 Hour Zone - Silent. - Upon detection, this zone

initiates a silent alarm, meaning that the sirens do not

function. Instead the PowerMaxComplete dials

telephone numbers and reports the event to central

stations and/or to private telephones, as programmed.

• 24 Hour Zone - Audible. - Upon detection, this zone

initiates a siren alarm. The PowerMaxComplete also

dials telephone numbers and reports the event to central

stations and/or to private telephones, as programmed.

APPENDIX E. PowerMaxComplete Compatible Devices

E1. PowerMaxComplete Compatible

Detectors

Each detector compatible with the PowerMaxComplete

system is packed with its own installation instructions.

Read them carefully and install as indicated.

A. PIR Motion Detectors

The wireless passive infrared (PIR) motion detectors used

in the system are of the PowerCode type. The

PowerMaxComplete is capable of “learning” each

detector’s identification code and linking it to a specific

zone (see par. 4.3 in this Guide). Some units are shown

below:

K9-85 MCW

MCPIR-3000

or K-940 MCW

DISCOVERY

K9-80/MCW

Note: K-940 MCW, Discovery K9-80/MCW and NEXT

K9-85 MCW are pet immune units.

In addition to its unique 24-bit identification code, each

detector transmits a message, containing status

information:

• The detector is in alarm (or not).

• The detector is being tampered with (or not).

• The battery voltage is low (or normal).

• “This is a supervisory message”.

If any of these detectors detects motion, it sends out a

message to the alarm control panel. If the system is in the

armed state, an alarm will be triggered.

B. Magnetic Contact Transmitter

MCT-302 is a PowerCode magnetic-

contact transmitter used to detect the

opening of a door or a window.

The alarm

contacts are closed as

long as the door or

window remains

closed.

MCT-302

The unit has an extra alarm input that acts as if it were a

separate wireless transmitter. It sends (or does not send) a

“restored to normal“ message to the alarm system,

depending on the setting of an on-board “DIP” switch. The

“restore” message informs you, through the control panel’s

display, whether the door or window is open or closed.

C. MCT-100 Wireless Adapter for Wired Detectors

MCT-100 is a PowerCode device used

mainly as a wireless adapter for 2 regular

magnetic switches installed on 2 windows in

the same room. It has two inputs, behaving

as separate wireless transmitters with

different PowerCode IDs. Each input sends

(or does not send) a “restored“ message to

the alarm system, depending on the setting

of an on-board “DIP” switch.

MCT-100

D. Wireless Smoke Detector

MCT-425. A photoelectric smoke

detector equipped with a

PowerCode-type transmitter. If

enrolled to a fire zone, it initiates a

fire alarm upon detection of smoke.

MCT-425

E. Glass Break Detector MCT-

501 An acoustic detector equipped

with a PowerCode-type transmitter.

Since it restores automatically after

detection, this unit does not send a

restoral message to the control

panel.

MCT-501

E2 PowerMaxComplete Compatible

Transmitters

The PowerMaxComplete system is compatible with multi-

button and single button key-ring and hand-held

transmitters that use PowerCode and CodeSecure coding

methods.

Multi-button PowerCode transmitters transmit the same

code each time the same button is pressed. They can be

used for emergency signaling, for activating the PGM

output. They can not be used for arming / disarming.

CodeSecure transmitters are of the rolling code type - they

transmit a new code each time the same button is pressed.

This provides a higher security level, especially in arming /

disarming applications, because the code can not be

copied (“grabbed”) by unauthorized people.

Following are the basic details of several compatible

transmitters. The possible applications for each push-

button are indicated in each drawing.

A. MCT-234

‘Keyfob’ transmitter. You

can program the AUX

(auxiliary) button to perform

various tasks, in

accordance with the user’s

needs.

Pressing AWAY and

HOME together for 2 sec.

initiates PANIC alarm.

Pressing AWAY for 2 sec.

initiates Latchkey arming.

DISARM

AWAY

AUX

HOME

MCT-234

B. MCT-231 / 201*

(N.A. in North America)

Single-button pendant units.

The MCT-231 (Code- Secure)

and the MCT-201

(PowerCode) can be enrolled

to perform functions as shown.

Both units look alike.

MCT-231 / 201

1 2 ... 27 28 29 30 31 32 33 34 35 36

Comments to this Manuals

No comments

Visonic POWERMAX - Specifications Page 32

Comments to this Manuals

Related products and manuals for Carbon monoxide (CO) detectors Visonic POWERMAX -