Visonic POWERMAX - Specifications download pdf (Page 16)

16 D-300885

4.4.10 Piezo Beeps

(Fig. 4.4, location 10). Here you determine whether warning

beeps will sound or muted during exit and entry delays. An

additional option is to mute the warning beeps only when the

system is armed “HOME”.

Options: enable beeps, off when home and disable beeps.

4.4.11 Trouble Beeps

(Fig. 4.4, location 11). Under trouble conditions, the

sounder emits a series of 3 short beeps once per minute.

Here you determine whether this special beeping

sequence will be active, inactive, or just inactive at night

(the range of “night” hours is defined in the factory). The 3

options are: enable beeps, off at night (8 PM through 7

AM) and disable beeps.

4.4.12 Panic Alarm

(Fig. 4.4, location 12). Here you determine whether the

user will be allowed to initiate a panic alarm by

simultaneous pressing either the two panic buttons

(on

the keypad / wireless commander) or away + home

(on a

keyfob transmitter). Audible panic activates the siren and

simultaneously transmits a message via telephone. Silent

panic only transmits a message via telephone. The

options are: silent panic, audible panic and disable

panic.

4.4.13 Swinger Stop

(Fig. 4.4, location 13). Here you determine how many times

each zone is allowed to initiate an alarm within a single

arming period (including tamper & power failure events of

detectors, PowerMaxComplete and wireless siren). If the

alarms number from a specific zone exceeds the

programmed number, the control panel automatically

bypasses the zone to prevent recurrent siren noise and

nuisance reporting to the central station. The zone will be

reactivated upon disarming, or 48 hours after having been

bypassed (if the system remains armed).

Available options are: shut after 1, shut after 2, shut

after 3 and no shutdown.

4.4.14 Cross Zoning

(Fig. 4.4, location 14). Here you determine whether cross

zoning will be active or inactive. Cross zoning is a method

used to counteract false alarms - an alarm will not be

initiated unless two adjacent zones are violated within a

30-second time limit.

This feature is active only when arming AWAY and only

with zone couples from zone No. 18 to 27

(18 and 19, 20

and 21, etc.). You may use any one of these zone couples

to create a “cross-zoned” area.

Note: If one of two crossed zones is bypassed (see Para.

4.4.8), the remaining zone will function independently.

Note: Every 2 crossed zones must be of the allowed zone

type (Interior, Perimeter, Perimeter follower).

The options are: cross zone ON and cross zone OFF.

Cross zoning is not applicable in Entry/ Exit zones and

24h zones (Fire, Emergency, 24h audible, 24h silent).

4.4.15 Supervision

(Fig. 4.4, location 15). Here you determine the time limit for

reception of supervision reports from various supervised

wireless devices. If any device does not report at least once

within the selected time limit, an “INACTIVITY” alert is

initiated. The options are: 1, 2, 4, 8, 12 hours and disable.

4.4.16 NOT READY

(Fig. 4.4, location 16). Here you determine if the system will be

NOT READY status when there is a supervision failure. In the

"in supervision" mode, the system will be in NOT READY

status if during the last 20 minutes a supervision message

was not received. Options: normal and in supervision.

4.4.17 AUX Button A

(Fig. 4.4, location 17). Here you select the function of the

AUX button on keyfob transmitters and wireless

commanders MCM-140+. Four options are offered for

each AUX button:

Status (applicable only to control panel that includes voice

option): Pressing the AUX button will cause the control

panel’s voice module to announce the system status.

Instant: Pressing the AUX button while the exit delay is in

progress will cause the system to arm “instant” (the entry

delay is canceled).

Skip exit delay: Pressing the AUX button will immediately

cause the system to arm “instant”.

PGM: Pressing the AUX button will activate the PGM

output (see further programming under “DEFINE

OUTPUTS”, par. 4.8).

4.4.19 Jam Detect

(Fig. 4.4, location 19). Here you determine whether

jamming (interfering trans- missions, on the radio channel

used by the system) will be detected and reported or not.

If a jam detection option is selected, the system does not

allow arming under the relevant jamming conditions.

Jam Detection Options

Option Detection and Reporting when

UL (20/20)

(USA standard)

There is continuous 20 seconds of

jamming

EN (30/60)

(Europe standard)

There is an accumulated 30 seconds of

jamming within 60 sec.

class 6 (30/60)

(British standard)

Like EN (30/60) but the event will be

reported only if the jamming duration

exceeds 5 minutes.

Disabled (no jamming detection and reporting).

4.4.20 Latchkey

(Fig. 4.4, location 20). Here you determine whether the

system can be armed in the latchkey mode. If the system

is armed this way, a “latchkey” message will be sent to

specific telephones upon disarming by a “latchkey user”

(users 5-8 or keyfob transmitters 5-8). This mode is useful

when parents at work want to be informed of a child’s

return from school. You can record a name for latchkey

users.

The options are: Latchkey ON and Latchkey OFF.

4.4.21 “Not Active”

(Fig. 4.4, location 21).

Here you determine the time limit for

reception of signals from sensors used to monitor the

activity of sick, elderly or disabled people. If no device

detects and reports movement at least once within the

defined time limit, a “not-active” alert is initiated.

Options: 3, 6, 12, 24, 48, 72 hours and no act disable.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 35 36

Comments to this Manuals

No comments

Visonic POWERMAX - Specifications Page 16

Comments to this Manuals

Related products and manuals for Carbon monoxide (CO) detectors Visonic POWERMAX -