Visonic POWERMAXCOMPLETE PANEL - User's Guide download pdf (Page 19)

SPECIAL FUNCTIONS

18 D-302755

6. Special Functions

Looking after People Left at Home

An important characteristic of the

PowerMaxComplete is its ability to function in a

mode contrary to the usual behavior of an alarm

system. When the system is in the disarmed state (or

even when armed “HOME” with perimeter protection

only), it can keep track of in-house activity and will

report lack of motion in interior zones if there is no

detection of motion within predetermined time limits.

To use this characteristic, you must ask your installer

to program a specific time limit beyond which lack of

motion will be reported as a “not active” alert.

To make things clear, let us assume that an elderly,

sick or handicapped person is left unattended in a

protected site. This person, disabled or sick as he

may be, will not stay entirely still for hours. It is only

natural that even while being asleep he will turn over

in his bed from time to time. He might also wander

into the kitchen to eat or drink, or to the bathroom for

other necessities. Upon doing so, the bedroom,

bathroom and kitchen motion detectors will detect his

movement.

If, for example, the “lack of motion” time limit is set by

your installer to 6 hours, a virtual 6-hour clock will

carry out a 6-hour “countdown”.

If motion is detected

within the 6-hour time frame, the

countdown will restart from the beginning (the virtual

6-hour clock will be “reset”) and no alert message will

be sent out.

If no motion is detected

within the 6-hour time frame

in any interior zone, the control panel will send a

“not-active” alert message to the central monitoring

station or to private telephones designated by the

installer.

IMPORTANT! In addition, you may provide the

person confined to interiors with a single-button

transmitter for distress situations, see next

paragraph.

Emergency Calls for Help

Suppose the disabled person discussed above has

an accident such as falling in the bathtub without

being able to get up. It might take hours before the

“No Active” alert is sent out, but he (or she) must be

assisted much sooner.

Even though the odds for such an accident are not

high, it is advisable to provide the disabled person with

a miniature, single-button pendant-type or wristwatch-

type transmitter. Pressing the button on this

transmitter will cause the PowerMaxComplete to send

an “emergency call” to the central monitoring station

or to private telephones designated by the installer.

To make this possible, ask your installer to define

one of the 28 zones of the PowerMaxComplete as an

emergency zone.

Then, obtain one of the transmitters listed below and

link this transmitter’s ID code to the emergency zone.

Compatible distress transmitters are (see Fig. 5):

MCT-201 - pendant-type

MCT-211 - wristwatch-type

MCT-101 - pocket-type

MCT-201

MCT-211

MCT-101

Figure 5. Single-button Emergency Transmitters

Remote Control by Telephone

control

panel

A. Establishing Telephone Communication

You can access the PowerMaxComplete system

from a remote telephone and perform arming and

disarming, activation and deactivation of electrical

devices and the auxiliary output (PGM), record,

playback and erase a voice message, and

investigate the system status. The process is shown

in the next illustration.

1. Dial the PowerMaxComplete tel. No.

2. Wait for 2-4 rings then hang

up.

3. Wait 12-30 sec.

4. Redial

PowerMaxComplete tel.

No. (Sound will be heard

for 10 sec.).

Not applicable

when dialing to the

GSM number of

the

PowerMaxComple

te. Proceed to

step 5.

5. [*} (to stop the sound)

6. [user code], [#]

[Desired command, see next table]

Notes

(1) The PowerMaxComplete responds in a similar

way if you just dial once and wait until you hear

telephone rings (in USA, for example, 11 rings).

(2) Entering of user code is required once only.

(3) If you wait more that 50 seconds (may change

according to setup / use) without keying a

command, the PowerMaxComplete will disconnect

the line.

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 45 46

Comments to this Manuals

No comments

Visonic POWERMAXCOMPLETE PANEL - User's Guide Page 19

Comments to this Manuals

Related products and manuals for Fire protection Visonic POWERMAXCOMPLETE PANEL -